Habari za Viwanda

Cable ya kakao haiwezi kupuuzwa

2021-03-05

Cable ya kakaounawezausipuuzwe

 

Kwa upimaji wa kebo ya shaba, tulijadili mengi juu ya yaliyomo kwenye kabati ya shaba iliyosokotwa yenye usawa, kama Jamii 6 (CAT 6), Jamii 6 (CAT 6A) na Jamii 8 (CAT 8). Ingawa aina hii ya utaftaji hutumiwa sana kusaidia usafirishaji wa sauti, data na video ya Ethernet, haimaanishi kuwa ndio aina pekee ya upigaji picha wa shaba ambao unaweza kukutana.

Cable ya kakao ("coax" in English) has long been used to transmit data and video signals. It is one of the first media to support 10BASE2 and 10BASE5 Ethernet, which unaweza achieve 10 Mb up to 185 meters or 500 meters, respectively. /s transfer. The term "coaxial" means that the central conductor of the cable and its shield have the same axis or center point. Some kexial coaxials may have multiple shielding layers, such as a four-shielded kexial coaxial. The cable contains two layers of shielding, and each layer of shielding is composed of aluminum foil wrapped with wire mesh. The shielding characteristics of kexial coaxial make it have strong anti-electromagnetic interference ability and unaweza transmit high-frequency signals over long distances.

Although we usually think that kexial coaxial is only used in broadband video and cable television (CATV) home applications, but in the commercial enterprise environment, from closed circuit television (CCTV), audio and video to radio frequency antennas, and even some network connections, you unaweza find Its figure. Therefore, it is very necessary to understand this cable medium and how to test it.

Aina kuu

There are many different types of kexial coaxials that support a wide range of professional applications, such as satellite communications, industrial, military, and marine applications. The three most common types of non-industrial kexial coaxials are RG6, RG11, and RG59, of which RG6 is most commonly used in applications such as CCTV and CATV in corporate environments. The center conductor of RG11 is thicker than RG6, which means that its insertion loss is lower and the signal transmission distance is longer. However, thicker RG11 cables are more costly and very difficult to bend, which makes them unsuitable for deployment in indoor applications, but more suitable for long-distance outdoor installations or straight backbone links. RG59 is more flexible than RG6, but its loss is higher. It is rarely used in other applications except for low-bandwidth, low-frequency analog video applications (rear-view cameras in automobiles) with short distances and limited wiring space.

 

Cable ya kakaospia zina tofauti tofauti-kawaida 50, 75, na 93Ω. 50Ω kexial coaxials have high power handling capabilities and are mainly used in radio transmitters such as amateur radio equipment, civil band radio (CB) and walkie-talkies. 75 Ω cables unaweza maintain signal strength well and are mainly used to connect various types of receiving equipment, such as cable television (CATV) receivers, high-definition televisions and digital video recorders. 93 Ω kexial coaxial was used in IBM mainframe networks in the 1970s and early 1980s, with very few applications and expensive. Although the 75 Ω kexial coaxial impedance is most commonly encountered in most applications today, it should be noted that all components in the kexial coaxial system should have the same impedance to avoid signal loss and signal loss at the connection point. Internal reflections that reduce video quality.

The digital signal 3 (DS3) signal used in the central office (also known as T3 line) transmission service also uses kexial coaxials, including 75 Ω 735 type and 734 type. The 735 type cable has a coverage distance of up to 69 meters, while the 734 type cable has a coverage distance of up to 137 meters. RG6 cable unaweza also be used to transmit DS3 signals, but the coverage distance is shorter.

For any kexial coaxial, successful installation depends on the use of high-quality components and correct installation techniques, especially the installation of connectors. Insertion loss is affected by the total length of the installed link and is the main parameter to ensure that the kexial coaxial supports the intended application.